Search results for query: Tornadoboy (1 - 25 of 75)
  Main search page Main search page   Next page Next

Subject Forum Poster Posted on
. Re: DU: Bradley Trainer

And a few more:
News Tornadoboy 10/17/17 04:35 AM
. Re: DU: Bradley Trainer

Here's a picture of the cab someone posted on KLOV:
News Tornadoboy 10/17/17 04:33 AM
. Re: DU: Bradley Trainer

I remember reading a magazine article that mention Bradley Trainer too and how arcade games had become so "advanced" that the military was l ...
News Tornadoboy 10/16/17 07:39 PM
. Re: Getting a good read off a bad EPROM

Your advice to use an older programmer WORKED, we now have what looks to be a complete set of the ROMs! X1000000 Thanks again for your advice!
EmuChat Tornadoboy 10/02/17 02:28 AM
. Re: Getting a good read off a bad EPROM

Turns out the man with the board has an EP-20 and is going to bring it in, so I'll take a shot at it with that too.
EmuChat Tornadoboy 09/28/17 07:34 PM
. Re: Getting a good read off a bad EPROM

I'm a noob so personally I couldn't be sure of anything, but I gave the dump to someone that definitely knows what they're doing and they're certain i ...
EmuChat Tornadoboy 09/28/17 12:10 PM
. Re: Getting a good read off a bad EPROM

Someone elsewhere also mentioned the idea of heating it too, is that worth a shot if all else fails?
EmuChat Tornadoboy 09/28/17 01:34 AM
. Re: Getting a good read off a bad EPROM

I just did some quick poking around and it looks like the EP-1 DOES support 27C512's There may be hope yet!
EmuChat Tornadoboy 09/28/17 01:21 AM
. Re: Getting a good read off a bad EPROM

The guy who owns the board with the EPROMs has an older programmer, I have no idea what type it is though, but I'll see if we can give it a shot on th ...
EmuChat Tornadoboy 09/28/17 01:09 AM
. Re: Getting a good read off a bad EPROM

I don't have it set up so I can't check, but can an EP-1 even read a 27C512? Also the GQ-4X says on the back it's made by GQ electronics, are are sa ...
EmuChat Tornadoboy 09/28/17 01:04 AM
. Re: Getting a good read off a bad EPROM

The programmer I initially used is a GQ-4X, and I have an old EP-1 I'm going to try too, I'm hoping to have access to the chip again this weekend. So ...
EmuChat Tornadoboy 09/28/17 12:59 AM
. Getting a good read off a bad EPROM

I've got a 27C512 EPROM from a prototype game that unfortunately is only giving a partial dump, I've heard it appears one address line isn't working, ...
EmuChat Tornadoboy 09/27/17 11:42 PM
. Re: Hacking the Arcadia Super Select System protection

I had to replace the sockets on the Piggyback board anyway so I figured I might as well strip it entirely (I LOVE my Hakko 808!) and scan the foil pat ...
EmuChat Tornadoboy 09/22/17 03:04 PM
. Re: Hacking the Arcadia Super Select System protection

I'm at work right now, but when I get home I'm going to spend an hour or so practicing some serious Google-fu which is what I should have done before ...
EmuChat Tornadoboy 09/19/17 03:02 PM
. Re: Hacking the Arcadia Super Select System protection

I saw them, although neither is a PAL8L14 but I saved them both as they may be useful. I've never heard of that game and it doesn't appear to be in MA ...
EmuChat Tornadoboy 09/19/17 04:28 AM
. Re: Hacking the Arcadia Super Select System protection

I just search the PAL archive and didn't find anything about dumping PAL8L14ACNS, and I went through the MAME Arcadia bios and game ROMs without findi ...
EmuChat Tornadoboy 09/19/17 04:06 AM
. Re: Hacking the Arcadia Super Select System protection

I think I've heard is what it does is juggle around the EPROM address lines. I was hoping that perhaps I can dump the PAL8L14ACNS (the PAL16 has been ...
EmuChat Tornadoboy 09/19/17 03:34 AM
. Hacking the Arcadia Super Select System protection

I've got a Leader Board Golf set (which I finally got working) that I'd like to be able to convert to other games made for this board set, which is th ...
EmuChat Tornadoboy 09/19/17 01:57 AM
. Re: Vectrex to a 19" arcade vector monitor conversion :)

Not to semi-hijack this thread, but do you know if it's possible to make a Vectrex main board from scratch or does it have custom/impossible to get pa ...
EmuChat Tornadoboy 08/25/17 01:17 AM
. Re: Need help building a Sente Moonquake

And here's a picture I believe shows the complete boardset, this, the previous photo I just posted and the one you linked to are the only photos I hav ...
EmuChat Tornadoboy 08/24/17 11:05 PM
. Re: Need help building a Sente Moonquake

I've got that picture, thanks! It's definitely useful, although it doesn't show the whole board and some of the IC numbers are tough to see. Here's a ...
EmuChat Tornadoboy 08/24/17 11:01 PM
. Need help building a Sente Moonquake

By an incredible stroke of luck someone at ACAM managed to get his hands on the ROM board for a super rare, prototype Sente game called Moonquake. The ...
EmuChat Tornadoboy 08/24/17 10:19 PM
. Re: Williams Predators for the first time in 30 years!

Congratulations to all involved in another incredible rescue of a lost game! There are truly some brilliant people involved in this hobby!
News Tornadoboy 07/29/17 11:17 PM
. Re: DU: Unbelievable news

Looks like pretty impressive use of the DECO hardware! Glad to see it saved, I know it's been a source of frustration to MAME for quite some time. T ...
News Tornadoboy 07/01/17 11:12 PM
. Re: Invisible Monsters

You know what would be awesome? If another set of the same ROMs turns up and is donated to MAME, thus making this guy's game worth jack!
News Tornadoboy 07/01/17 08:19 PM

Search results for query: Tornadoboy (1 - 25 of 75)
  Main search page Main search page   Next page Next